About the Company
Tapco Roofing Products
Company Profile

Standard galvanised roofing "clout" nails or outdoor (yellow passivated) Phillips Counter-sunk-type screws fixed directly through the...

Who We Are
Tapco Roofing Products
About the Company
Company introduction
Contact the Company
Company Introduction
Standard galvanised roofing "clout" nails or outdoor (yellow passivated) Phillips Counter-sunk-type screws fixed directly through the moulded-in fixing guides. 30mm in length for the slates, 50mm in length for the Ridge & Hip Caps (or 75/80mm when fixing over RidgeMaster/HipMaster). Note that Stainless Steel fixings should be used on roofs within 2 miles of a coastal area and are compulsory for use throughout Scotland (stipulated by Scottish Local Building Control)Just like a natural slate, this depends on the pitch of the roof. The lower the pitch, the less "exposure" of each slate course, so measure the pitch first and fitment to a square metre is: between 12 to 25-degrees equals 22 slates per square metre (6" Exposure); 25 to 27.5-degrees equals 20 slates per square metre (6.5" Exposure); 27.5 to 30-degrees equals 19 slates per square metre (7" Exposure); and over 30-degrees equals 18 slates per square metre (7.5" Exposure).The maximum pitch TapcoSlate can be fitted to is 70-degrees. Over 70-degrees is classed as a "cladding" product; TapcoSlate is classed as a "roofing" product and so should not be fitted over 70 degrees unless advice is requested from your Local Building Authority Office with regards to possibly fitting at this higher pitch.Yes. Standard slating principles apply. An extra 3.5 slates per linear metre of eaves should be ordered to create the eaves/starter course slates - a starter tile is created by cutting a standard TapcoSlate down to 305mm (see our Fixing Guide for further information).Nailed/screwed in situ and overlapped as a dry-fix system which is much more secure than a mortar-bedded ridge. Nails/screws should be 50mm in length for the Ridge & Hip Caps (or 75/80mm when fixing over RidgeMaster/HipMaster). DO NOT over expose the caps, these should be set at a 6" exposure, and calculated at 6 Caps per linear metre of ridge and/or hip.Algae grows on a laminar material, TapcoSlate is not laminar, so any growth will not stick to the slates and can easily be removed. To permanently deter growth, install a 5cm wide copper strip just below the ridgeline, this will create a copper sulphate solution which will discourage any growth. We also have a Care & Maintenance guide available from our website Documents Centre.It’s not made from recycled materials… but it’s RECYCLABLE at the end of its long lifespan. TapcoSlate is made from limestone and virgin polypropylene. Consequently, there is greater control over the mix and the manufacturing process. The main problems experienced with using reclaimed, inconsistent raw materials are due to the lack of control in the manufacturing process which can have unpredictable results. There are no such problems with TapcoSlate.Not without consulting your local building control office. TapcoSlate and DaVinci Select Shake is fire rated for roofing structures up to 70-degrees, above this is classed as "Cladding" which involves a different product fire rating. Building control may approve the product for use as vertical cladding if an approved firewall is put in place, but please speak to your local office first!No. TapcoSlate slate and ridge/hip caps need to be mechanically fixed to the roof with either nails or screws. A glue formulated for polypropylene can be used in the assembly of accessories such as ridge-to-hip junctions and ridge/hip end cap pieces. We recommend the use of PERMABOND® TA4610 or TA4620 for accessory creation unless you have polypropylene welding equipment.Yes. Use 18mm thick boards to avoid fixings penetrating the underside of the board. Note that a smaller length (25mm) nail or screw can be used for the eaves/starter course to avoid penetration under the board on this particular course of slates.Yes. Solar panels can be fitted to TapcoSlate without problems, the slate does not break and so solar frames can be fitted, or the slate can work around a solar framework, depending on the type of solar installation. The only thing we stipulate is that the solar panels are fitted to the manufacturers specifications and that the panels are secured to the wooden roof structure and not just to the slate itself to hold them in place. Note that Westlake Tapco Europe Limited does not warrant third-party installations such as solar panels and warranty should be sought from the panel manufacturer.We recommend the use of an impermeable (non-breathable) roofing membrane such as Protect Wunderlay. Impermeable membrane prevents water vapour from passing through the membrane and therefore the slates can be fixed directly to board or batten with a mechanical ventilation channel installed underneath the membrane (or OSB/ply on a fully-boarded system). When using a permeable (breathable) membrane, the membrane needs to be ventilated over the top, as water vapour penetrates through it, this means the use of a more expensive counter batten system being fitted directly underneath the slates, on top of the permeable membrane, and this void to be mechanically ventilated to allow the membrane to function correctly. Fitting an impermeable membrane is the most cost-effective and efficient way to fix TapcoSlate as they are classed as an "insufficiently air-open" roof covering with regards BS 5250, so be sure to mention this to any membrane supplier when seeking advice.
Visit Official Website
Get in Touch

Let’s build something together.

Contact Tapco Roofing Products to discuss your requirements.

Tapco Roofing Products
Official website

Tapco Roofing Products